How to Replace a Bathtub in Your Bathroom
How to Replace a Bathtub in Your Bathroom
Blog Article
The article in the next paragraphs pertaining to How to Install a Bathtub Yourself is amazingly captivating. You should give it a look.
Setting up a bath tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, and often, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard job. If the old bathtub is readily easily accessible, the task can move easily; if you have to open a wall surface to remove the old tub and also position the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the work and are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to consider utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube links.
This article will assist you mount a new tub in your shower room if you have actually already bought a new bathtub as well as do not need to change the plan of your previous water pipes.
Your tools as well as product list need to comprise the following:
Planning for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next goal is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub till the spirit level reads degree.
To install taps, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water system and also inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill the tub and likewise check the overflow electrical outlet and the typical outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used a minimum of when as this will resolve it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in place in between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap ends first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can split relatively early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about Tools You Need to Install a New Bathtub . Thank you for taking a few minutes to browse our post. Enjoyed our review? Please share it. Help other people check it out. Thank you so much for your time spent reading it.
Pricing Report this page